1. A smaller autonomous system (AS) is
defined inside the boundaries of a larger AS, and both of them employ MPLS to
forward packets. A label switched path (LSP) has already been established from
end-to-end between edge Label Switched Routers (LSRs) from the larger AS. This
LSP tunnels through the smaller AS. In this scenario, what mechanism does MPLS
provide in order to minimize routing information maintenance in the internal
LSRs of the smaller AS ? Describe in detail how this mechanism works as a
labelled packet is forwarded through the smaller AS.
MPLS uses a stack of labels.
- When a transit packet arrives with its own label corresponding to an external LSP, the ingress LSR of the smaller AS pushes a new label onto the label stack.
- This new label corresponds to an internal LSP within the smaller AS
- The internal LSRs of the smaller AS switch the packet through to the egress LSR, working only on the topmost label (the new label)
- At the egress LSR of the smaller AS, the new label is popped off the stack restoring original label.
- The packet resumes its travel using the original external LSP for the larger AS.
2. What is the motivation behind the use of
Penultimate Hop Popping in an MPLS network ? Describe briefly how it works.
It provides a form of optimization to
minimize the performance penalty incurred when the egress LSR of a MPLS network
has to perform two lookup operations when processing a label stack. When a
packet with a stack of two labels arrives at the penultimate LSR (the LSR
before the egress LSR), it pops the top stack before forwarding it onwards to
the last stack.
3. Distinguish between the independent and
ordered control approach to exchanging labels in the Label Distribution
Protocol (LDP).
Independent control - Each LSR advertises
label mappings at will. In an unsolicited mode, LSRs will generally advertise
new labels whenever the IP routing information changes.
Ordered control - In this mode, all path advertisements originate at the
egress router, and the label advertisement messages travel upstream to the
ingress router. For advertisement on demand, a request from the ingress router
triggers a chain of requests downstream to the egress router
4. Explain, with the aid of a diagram, how
the liberal approach to label retention works in the LDP ? What advantage does
the liberal approach offer over the conservative approach, and what is its
corresponding disadvantage ?
It retains all label mappings even if they
don’t correspond to an existing LSP.
- Advantage: If the next hop path changes for the LSP, the given LSR may already have a new LSP ready, so it can react to the routing change almost immediately. Whereas in conservative approach, the LSR will need to request label mappings first from alternative downstream LSRs in the neighbourhood.
- Disadvantage: Larger mapping table space required to keep all the labels, as well as network overhead in label exchange when the number of neighbouring LSRs is very large.
5. Explain two approaches that could be
employed to address the potential problem of loops in the label distribution
protocol (LDP)
·
The hop count field in the
label request message is incremented by all LSRs that the message passes
through. If the hop count ever reaches a maximum value, a loop has occurred and the LSR sends a LDP
notification message to the originator of the message.
- Path vectors - Each router inserts its own LSR ID in the path vector field of the message, and if it ever finds its own ID here in a newly received message, it breaks the loop
6. Name the two situations in which a LSR in the middle of a LSP may
need to return an Internet Control Message Protocol (ICMP) error message to a
datagram’s source. What is the problem with using ICMP in a Virtual Private
Network (VPN) deployed using MPLS, and how is this addressed by the LSR that
wishes to create the ICMP message ?
Two situations:
- The datagrams hop limit may run out
- The packet may encounter a problem in a link between routers (link broken, or datagram too large to be fragmented and sent over link)
In a VPN, only the egress router at the
boundary of the VPN is able to access the source IP address. Other intermediate
routers cannot access the source IP address (which is encrypted using IPSec),
and hence cannot route the appropriate ICMP message back to the source.
This is addressed by creating a ICMP
message and adding the original stack label from the packet that caused the
error. This ICMP datagram will follow the route of the original packet to the
egress router, who can then successfully route it back to its source.
7. How might a session initialization
deadlock occur during the LDP of a MPLS ? Explain how this can be overcome
using the LDP hello message.
Refer to the exhibit. A technician applies the configuration in the exhibit to a clean router. To verify the configuration, the technician issues the show running-config command in the CLI session with the router. What lines should the technician expect to see in the router output from the show running-config command?
Refer to the exhibit. A network administrator on HostA has problems accessing the FTP server. Layer three connectivity testing was successful from HostA to the S1 interface of RouterB. Which set of commands will allow the network administrator to telnet to RouterB and run debug commands?
The connection between routers B and C has been successfully tested. However, after rebooting router C, the administrator noticed the response time between networks 10.10.3.0 and 10.10.4.0 is slower. Ping between the two routers is successful. A trace route indicates three hops from router B to router C. What else can be done to troubleshoot the problem?
The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
Refer to the exhibit. The output is shown for the show ip route command executed on Router A. What does the IP address 192.168.2.2 represent?
Refer to the exhibit. What additional command is required to allow remote access to this switch from hosts outside the local network?
Refer to the exhibit. Which names correctly identify the CLI mode represented by the prompt for Switch-East4#? (Choose two.)
Refer to the exhibit. What command will place the router into the correct mode to configure an appropriate interface to connect to a LAN?


Refer to the exhibit. A student is responsible for the IP addressing, configuration and connectivity testing of the network shown in the graphic. A ping from host B to host C results in a destination unreachable but a ping from host B to host A was successful. What two reasons could account for this failure based on the graphic and partial router output for the Dallas router? (Choose two.)
Refer to the exhibit. A student working in the lab selects a cable that is wired as shown. Which connection types can successfully be made with this cable? (Choose two.)
Refer to the exhibit. What destination IP address will PC1 place in the header for a packet destined for PC2?
Refer to the exhibit. Based on the IP configuration shown, what would be the result of Host A and Host B attempting to communicate outside the network segment?
Refer to the exhibit. How many subnets are required to support the network that is shown?
Refer to the exhibit. A student is setting up a home network primarily used for extensive file transfers, streaming video, and gaming. Which network device is best suited to these types of activities in the topology shown?
Refer to the exhibit. A network administrator has decided to use packet capture software to evaluate all traffic from the student subnet on the way to the Internet. To ensure that all packets are captured, what network device should be used to connect the monitoring station to the network between R1 and R2?
Refer to the exhibit. Assume that all devices are using default settings. How many subnets are required to address the topology that is shown?
Refer to the exhibit. Which three statements are true about the exhibited topology? (Choose three.)
Refer to the exhibit. Which three statements identify the type of cabling that would be used in the segments that are shown? (Choose three.)
Refer to the exhibit. A network technician has been allocated the 192.168.1.0/24 private IP address range for use in the network that shown in the exhibit. Which subnet mask would be used to meet the host requirements for segment A of this internetwork?